Our Expertise: 5) Research

2) Biomechanics

3) Engineering

4) Animation

5) Research
  Knee Injury
  Child Safety
  Slip/Trip and Fall
  Rear-End Impact
  Human Testing
  Bicycle Rider Testing

6) Case Studies

Meniscus

In an ongoing project directed by Jeff Wheeler of Vector Scientific, in collaboration with Joel M. Bach, Ph.D. of The University of Colorado Health Sciences Center (USHSC) Department of Orthopaedics Biomechanics Laboratory, a special test apparatus was custom built to hold cadaveric leg specimens at desired flexion angles and to apply desired pre-impact knee joint compression. The knee fixture is then accelerated into a dashboard at desired velocities to simulate occupant knee impacts.

Lindsay Harris, M.D. of The University of Colorado Health Sciences Center (UCHSC) Department of Orthopedics is conducting pre and post-test arthroscopic surgery to evaluate the meniscus pathology.
^back to top^

Child Occupant Safety Research

Jeffrey Wheeler researched the efficiency and fit of booster seats for children around 4 years of age. Many state laws now require that a child be restrained in a car seat until 4 years of age or at least 40 pounds. Once a child is too large for a car seat, it is recommended that they use a booster seat, which adjusts the adult seatbelt to fit the smaller dimensions of a child. However, many parents do not utilize booster seats for their children since they are not required. Most children, once they reach the age of 4 years, use the standard seat and seatbelt system available in the vehicle.

There is a gap in the car safety research for children in this transitional age range. This makes any and all data collection using child volunteers extremely valuable in the advancement of child safety in automobiles.

One of Mr. Wheeler's associates, collected data regarding booster seat versus adult seatbelt fit from over 100 children around 4 years of age with the permission of their parents from ABC Child Development and Community Services and YMCA child care facilities in southern California. Presentations and educational material were provided regarding child occupant safety to the parents and childcare providers at the institutions participating in the research project.

The results of this study have been submitted for peer-review publication. The results will be used to educate parents and childcare providers about the importance and benefits of booster seats, as well as to provide additional data to the scientific community.
^back to top^

Slip/Trip and Fall Research and Slip Resistance Testing

Vector Scientific staff members collaborated with Chris Powers, Ph.D. at the University of Southern California (USC) Musculoskeletal Biomechanics Research Laboratory (see related links) and Jim Flynn, P.E. of J2 Engineering, Inc. in Fresno, California to study slip and fall dynamics. Shown here is a portable tribometer (English XST – see related links) on a force plate to evaluate slip resistance.

Results were presented to the American Society of Testing and Materials (ASTM) F-13 Committee on Safety and Traction for Footwear and were published in the Journal of Testing and Evaluation (November 1999, Repeatability and Bias of Two Walkway Safety Tribometers).
^back to top^

Low-Speed Rear-End Impact Testing

Vector Scientific staff members, in collaboration with MacInnis Engineering Associates, Ltd. completed a grant funded research project entitled "Identification of Injury Mechanisms in Low-speed Rear-end Automobile Impacts."  This study was funded in part by a grant from Technology BC Investments in Research and Development, administered by the Science Council of British Columbia.

This project involved more than 80 tests with live human subjects during controlled low-speed, rear-end impacts. Occupant kinematics, kinetics, muscle activity patterns, and clinical symptoms were measured, analyzed, and interpreted. Live human subject neuromuscular and musculoskeletal response to rear-end collisions provided knowledge toward understanding the mechanism of injury causing whiplash-associated disorders, human tolerance, and human head/neck kinematics. This information is necessary to validate mathematical and physical models used for seat back and head restraint designs.
^back to top^

Human Subject Testing

High-speed cameras were used to capture head and neck kinematics during the impacts.  Head and chest accelerometers were also used to measure occupant dynamics.

Pre and post-test clinical data including MRI, range of motion, strength, and pain experience questionnaires were collected.

A telemetry EMG system was used to monitor and record the subjects' cervical muscle response during the impacts.

^back to top^
Bicycle-Rider Testing

Bicycle-rider dynamics have been measured to gain insight into the mechanism of traumatic and overuse injuries during cycling.
^back to top^